• An encyclopedia of Cuban cigars

Guides

How to Build a Humidor: Materials, Design and Seasoning

By Vitola Room Editorial TeamVitola Room Editorial · 6 min read

A humidor is an airtight, humidity-regulated container for cigars, traditionally lined with Spanish cedar. A homemade one needs a tight seal, a wood that does not taint the tobacco, no strong-smelling finishes or glues, a humidification source and a hygrometer. This article covers the principles of building one, not a shopping list or a set of plans.

Cigars are tobacco products: they are harmful and addictive, and this guide is written for adults. Woodworking also carries its own risks, so wear gloves and eye protection when handling tools and work with good ventilation.

What a humidor must do

Every working humidor, whatever its size, meets four requirements. If a design fails any one of them, the cigars inside will drift out of condition.

  • Seal: the lid and body must close closely enough to slow the exchange of air with the room.
  • Wood: the interior must take up and release moisture steadily, and must smell of nothing that could pass to the tobacco.
  • Humidification: something must supply water vapour to replace what escapes. The principle is explained in how a humidor works.
  • Measurement: a hygrometer you can trust, so that you adjust from a reading rather than a guess.

The same four requirements apply at three scales: a small box, a cabinet and a whole room. Only the way each one is delivered changes.

Choosing the wood

Spanish cedar is the traditional choice. It comes from trees of the genus Cedrela, commonly Cedrela odorata, which belong to the mahogany family despite the name. It has a gentle aroma, a fine even grain, behaves steadily with moisture and is comfortable to cut and fit, which matters when you are trying to make tight joints. The reasons are set out in why humidors use Spanish cedar.

The woods to avoid are those with a strong or resinous smell, such as pines and aromatic red cedar, because their scent can transfer to the cigars. A useful rule is to smell the bare board before you commit to it: if the odour is sharp or sticky, it does not belong inside a humidor. The same applies to boards that have been treated, stained or sealed by the supplier.

Neotropical Cedrela species, Cedrela odorata among them, are listed in Appendix II of CITES, so international trade in the timber needs permits, and it is sensible to ask a supplier where the wood comes from and what documentation exists.

Designing the box

A small box is far easier to get right than a large one. The design decisions that matter most are these.

Joints

Well-fitted joints do most of the sealing work. Gaps at the corners of the carcass are a common source of slow leaks, so it is worth cutting and test-fitting before any adhesive is used.

Lid, hinges and closure

The lid should meet the rim evenly all the way round. Hinges that do not twist the lid as it closes help a great deal, and a lip or a thin seal around the rim improves contact. Perfect airtightness is neither achievable nor necessary: the lining and the humidifier are there to cope with a little exchange. The aim is a box whose reading changes slowly.

Interior layout

Leave room for the humidification device and the hygrometer, and for air to move around the cigars. Dividers and trays should be made of the same wood as the lining.

Glues, finishes and what to avoid

Anything that gives off a smell can end up in the cigars, because tobacco absorbs odours readily. Check the manufacturer's data sheet for each product and let everything cure fully before the box is used. The table below is a rule of thumb, not a guarantee.

MaterialSuitable?Reason
Unfinished Spanish cedar interiorYesNeutral aroma; takes up and releases moisture
Resinous or strongly scented softwoodsNoTheir scent can taint the tobacco
Varnish, lacquer or stain on the interiorNoSeals the wood so it cannot buffer moisture, and can give off odours
Solvent-based or strongly scented adhesivesAvoidFumes can linger in the wood
Low-odour adhesive, used sparingly and fully curedUsually acceptableConfirm with the manufacturer's data sheet
Exterior finish, kept off the liningAcceptable with careCure it fully and keep it away from interior surfaces

Adding humidification and a hygrometer

Choose the humidifier to suit the size of the box. Options include foam or gel devices charged with distilled water or a glycol solution, and sealed packs that either release or absorb moisture. Their strengths and limits are covered in propylene glycol humidifiers and two-way humidity control packs.

Place the hygrometer where you can read it without holding the lid open, and check it before you rely on it. Cheap gauges can be well out; the method is described in calibrating a hygrometer.

Testing the seal and seasoning the finished box

Before any cigars go in, test the seal. Close the lid over a strip of paper at several points round the rim; if it slides out with no resistance at one spot, the contact is uneven there. A torch shone inside the closed box in a darkened room can also reveal gaps in the joints.

Then season the box. Bare wood is dry and will draw moisture out of cigars, so it needs conditioning first, with a damp (not dripping) humidifier in the closed box while you watch the hygrometer. Do not wipe the interior with a wet cloth or spray it heavily, because soaked wood can warp, crack or loosen joints. The full method and a realistic timeline are in seasoning a new humidor. A homemade box deserves a little extra patience, since you are also learning how well it holds a reading.

From box to cabinet to room

As the volume grows, small leaks matter more and a single passive humidifier is less likely to be enough. Larger cabinets and rooms usually need more than one humidification source, some way of keeping the air moving, and a plan for the door. A room also has to cope with people coming and going, so the doorway, walls and floor become part of the seal, just as the lid was for the box. The trade-offs between sizes are discussed in cabinet versus desktop humidors.

When a repurposed container is enough

Not every project needs carpentry. A sealed plastic container can do the same job with far less effort, and it is described in tupperdors and coolidors. If you have inherited an old wooden box instead, read restoring a vintage humidor before building anything new.

Frequently asked questions

How do I build a humidor?

Start with a small box made from Spanish cedar, with tight joints and a lid that closes evenly. Use low-odour adhesive, leave the interior unfinished, fit a humidification device and a hygrometer you have checked, then test the seal and season the box before adding cigars.

How do I make a humidor?

The process is the same: an airtight box, a suitable lining wood, no strong smells from glues or finishes, a humidification source and a hygrometer. Making one at home is mainly about careful joinery and patient seasoning.

How do I build a humidor cabinet?

A cabinet follows the same four requirements as a box, but with more volume to seal and humidify. Expect to need tight doors, a cedar-lined interior, more than one humidification source and a way to keep air moving. Test the seal and season it thoroughly before loading cigars.

What wood is best for a humidor?

Spanish cedar is the traditional choice because of its mild aroma and steady behaviour with moisture. Avoid resinous or strongly scented woods, which can pass their smell to the tobacco.

Can I use a cooler instead of a built humidor?

A sealed cooler or plastic container can hold humidity, though it has no cedar lining. See tupperdors and coolidors for how these work and what they lack.

Reader questions

Questions & answers

No questions yet. Ask the first one.

All articles